自從碳氫清洗機問世以來，它一直受到精密零部件行業的青睞。一方面，它可以實現高質量的清潔，另一方面，它可以減少污染。畢竟，污染是精密儀器的天敵。碳氫清洗機在使用中有很多優點，但這些優點的成本是操作更麻煩，由于操作錯誤會出現故障，所以我們應該注意以下注意事項。

Since the hydrocarbon cleaning machine came out, it has been favored by the precision parts industry. On the one hand, it can achieve high-quality cleaning, on the other hand, it can reduce pollution. After all, pollution is the natural enemy of precision instruments. The hydrocarbon washer has many advantages in use, but the cost of these advantages is that it is more troublesome to operate. Because the operation error may cause failure, we should pay attention to the following precautions.

碳氫清洗機在使用時要求非常好，清洗機的進水壓力應為0.3～0.5MPa在此范圍內，此外，在使用碳氫清洗機時，您還需要定期檢查和清潔進水過濾器和過濾器，并確保其過濾器清潔和暢通。這是一個非常重要的一點。如果長時間堵塞，仍然會對設備的運行效果產生很大影響，嚴重時會損壞設備。因此，定期檢查也是一個不容忽視的問題。

The hydrocarbon washer is required to be very good in use, and the water inlet pressure of the washer should be within the range of 0.3~0.5MPa. In addition, when using the hydrocarbon washer, you also need to regularly check and clean the water inlet filter and filter, and ensure that the filter is clean and unblocked. This is a very important point. If it is blocked for a long time, it will still have a great impact on the operating effect of the equipment, and in serious cases, it will damage the equipment. Therefore, regular inspection is also a problem that cannot be ignored.

此外，員工在使用碳氫清洗機時也會定期檢查機油。如果他們想更換潤滑油，他們應該根據需要更換潤滑油。在冬季，他們還應做好防凍工作。松開螺旋泵頭和過濾器柱頭，排水并倒入防凍液。

In addition, employees also regularly check the oil when using the hydrocarbon washer. If they want to change the lubricant, they should change the lubricant as needed. In winter, they should also do a good job of antifreeze. Loosen screw pump head and filter head, drain water and pour antifreeze.

使用時，建議檢查柱塞密封是否泄漏。如果發現泄漏或有更多水滴泄漏，應及時更換柱塞密封。在年底前的工作中，須按下關閉前釋放的壓力，按下紅色壓力釋放按鈕并點亮，然后等待綠燈熄滅。當壓力為0時，設備空載運行2~3分鐘后關掉電源。

When using, it is recommended to check the plunger seal for leakage. If leakage or more water drops are found, replace the plunger seal in time. During the work before the end of the year, press the pressure released before closing, press the red pressure release button and light it up, and then wait for the green light to go out. When the pressure is 0, turn off the power after the equipment runs for 2-3 minutes without load.

要定期檢碳氫清洗設備，避免設備故障影響清洗；注意清洗設備的功率調節，功率過大可能會打傷產品；風干設備調整干燥參數。應使用干凈無污染的油抽取清洗劑，取液后及時封蓋，避免揮發損耗。更多相關事項就來我們網站www.chendakeji.cn咨詢吧！

The hydrocarbon cleaning equipment shall be inspected regularly to avoid equipment failure affecting the cleaning; Pay attention to the power regulation of the cleaning equipment. Excessive power may damage the product; Air drying equipment adjusts drying parameters. Clean and pollution-free oil shall be used to extract the cleaning agent, and the liquid shall be timely covered to avoid volatilization loss. For more information, please visit our website www.chendakeji.cn!